💡 Introduction

In this guide, we’ll show you how to replace the microphone in your MacBook Pro 13-inch (Early 2011).
Agar aapka MacBook ka mic kaam nahi kar raha ya sound distorted aa raha hai, toh is guide se aap usse replace kar sakte ho.

🧰 What You’ll Need

  • Phillips #00 screwdriver

  • Torx T6 screwdriver

  • Spudger (plastic pry tool)

  • Replacement microphone module

  • Thoda patience aur careful handling 😅

🔩 Step 1: Remove the Lower Case

  • Flip your MacBook upside down.

  • Remove 10 screws:

    • 3 × 14.4 mm Phillips #00

    • 3 × 3.5 mm Phillips #00

    • 4 × 3.5 mm shouldered Phillips #00

  • Jab small screws wapas lagao, thoda angle mein daalna (case thoda curved hota hai).

⚙️ Step 2: Take Off the Lower Case

  • Fingers se vent area ke paas se case ko thoda pry karo.

  • Slowly lower case ko utha ke side mein rakho.

🔋 Step 3: Disconnect the Battery

  • Spudger ka use karke battery connector ko logic board se gently upar ki taraf lift karo.

  • Corners se dhire-dhire pry karo — zyada force mat lagao.

Step 4: Bend Battery Cable Out of the Way

  • Battery cable ko thoda side mein bend kar do taaki kaam karte waqt accidentally connect na ho jaye.

🌬️ Step 5: Disconnect the Fan Connector

  • Spudger se fan connector ko seedha upar ki taraf lift karo.

  • Thoda twist motion use karo taaki socket pe stress na pade.

  • Dhyaan rahe, plastic fan socket fragile hota hai — todna nahi hai 😅.

Step 6: Remove the Fan Screws

  • Fan ke 3 screws nikaalo:

    • 1 × 7.2 mm T6 Torx

    • 2 × 5.3 mm T6 Torx

  • Ab fan ko gently upar uthao aur side mein rakho.

Step 7: Disconnect Cables from Logic Board

  • Spudger se neeche diye gaye cables gently disconnect karo:

    • Right speaker / subwoofer cable

    • Camera cable

    • AirPort / Bluetooth cable

    • Optical drive cable

    • Hard drive cable

    • Trackpad cable

Step 8: Disconnect Keyboard Ribbon Cable

  • Keyboard ke ZIF socket ka small locking flap flip up karo.

  • Phir ribbon cable ko softly bahar nikaalo.

  • Agar tight ho, tape lagake pull karna easy hota hai.

Step 9: Disconnect Keyboard Backlight Cable

  • Agar black tape lagi ho socket pe, pehle usse remove karo.

  • Phir backlight cable ke ZIF socket ka flap open karo aur cable bahar nikaalo.

Step 10: Disconnect Sleep Sensor / Battery Indicator Cable

  • Spudger ke flat end se is connector ko gently upar lift karo.

Step 11: Disconnect Display Data Cable

  • Display data cable ke black plastic tab ko DC-In board side ki taraf rotate karo.

  • Phir cable ko socket se seedha bahar kheenchna hai, upar nahi — warna socket toot sakta hai.

Step 12: Remove Logic Board Screws

  • Logic board ko hold karne wale screws nikaalo:

    • 5 × 3.6 mm T6 Torx

    • 2 × 4.3 mm T6 Torx

    • 2 × 7.2 mm T6 Torx

  • Screw sizes thodi vary kar sakti hain depending on model.

Step 13: Remove Display Data Cable Retainer

  • 2 screws nikaalo:

    • 1 × 8.6 mm Phillips

    • 1 × 5.5 mm Phillips

  • Phir display data cable retainer ko remove karo.

Step 14: Peel Off the Microphone

  • Spudger ki tip se microphone ko us adhesive se gently peel karo jahan woh upper case pe chipka hota hai.

  • Dheere-dheere uthao, wire ko pull mat karo.

Step 15: Remove the Logic Board

  • Optical drive side se logic board ko thoda upar uthao.

  • Ensure sab connectors free ho aur DC-In board cable fasa na ho.

  • Logic board ko carefully lift karke bahar nikaalo.

Step 16: De-route the Microphone Cable

  • Microphone cable ko left speaker housing ke groove se nikaalo.

Step 17: Remove Tape Over Microphone Connector

  • Mic connector pe lagi black tape ko gently peel karo.

Step 18: Disconnect Microphone Connector

  • Spudger se wire ke neeche se lift karo aur mic connector ko logic board se disconnect karo.

Step 19: Remove the Microphone

  • Ab microphone module ko logic board se completely remove kar lo.

  • Bas — old mic out! 😄

🔁 Reassembly

To put everything back together, follow all the steps in reverse order:

  • Naya microphone install karo.

  • Sab connectors dubara attach karo.

  • Logic board, fan, aur lower case ko reinstall karo.

  • Battery ko last mein reconnect karo.

💡 Final Tips

  • Saare connectors tight fit hon aur cables pinched na ho.

  • System ko power on karke mic test kar lo (use “Voice Memos” or “QuickTime”).

  • Agar voice clear aa rahi hai — mission successful! 🎉

Scroll to Top